ماژول کنترلر دما و رطوبت XY-TR01 دارای نمایشگر OLED

دانشجو بن، امتیاز خرید کاربران دائمی
با سفارش این محصول شما 4  امتیاز دریافت میکنید
ارزش امتیاز دریافتی:  4,000تـومان
حد اکثر تخفیف قابل استفاده برای این محصول 4 امتیاز که برابر است با 4,000تـومان

DKP - 41410

محصول جدید

17 عدد موجود در انبار

184,000تـومان

Temperature Function:
1>. Automatic recognition of working mode:
The module automatically selects the working mode according to the Start Temperature and Stop Temperature.
Start Temperature is more than stop temperature, Turn ON cooling mode 'C'.
Start temperature is less than stop temperature, Turn ON heating mode 'H'.
2>. Cooling Mode 'C':
Relay turn ON and Red Indicator turn ON and Refrigeration equipment starts working if connect load when Current Temperature is more than Start Temperature.
Relay turn OFF and Red Indicator turn OFF and Refrigeration equipment stops working if connect load when Current Temperature is less than Stop Temperature.
3>. Heating mode 'H':
Relay turn ON and Red Indicator turn ON and Heating equipment starts working if connect load when Current Temperature is less than Start Temperature.
Relay turn OFF and Red Indicator turn OFF and Heating equipment stops working if connect load when Current Temperature is more than Stop Temperature.
4>. Temperature Correction ‘ OFE ’(-10.0~10.0℃):
The system may have errors if it works for a long time, it can be corrected by this function.
Actual Temperature = Measured Temperature + Calibration Value.
Setting method:
4.1>.Double-click button 'TM+' in the normal running interface into Temperature Correction setting interface.The first line shows the type of correction value(OFE or RH).The second line shows the specific value.
4.2>.Switch to select modified parameters by short press button ‘TM-’.
4.3>.Short press button ‘RH+’ and ‘RH-’ to set the specific value.Support long press.
4.4>.After the parameters have been modified, double-click button ‘TM+’ to save the data and exit the correction value setting interface.
5>. Set Start/Stop Temperature:
Keep press button 'TM+' for 3second in the normal running interface into Start Temperature setting interface.Short press button 'TM+' or 'TM-' to set parameters value.After the parameters are modified and then wait for 6s to automatically save and exit.
Keep press button 'TM-' for 3second in the normal running interface into Stop Temperature setting interface.Short press button 'TM+' or 'TM-' to set parameters value.After the parameters are modified and then wait for 6s to automatically save and exit.
6>. Relay enable (default on):
Short press button ‘TM-’ in the normal running interface.Turn ON or OFF temperature relay output enable.Screen will display ‘℃’ and flashes if If the temperature relay is OFF.

Humidity Function:
1>. Automatic recognition of working mode:
The module automatically selects the working mode according to the Start Humidity and Stop Humidity.
Start Humidity is more than stop Humidity, Turn ON dehumidification mode 'd'.
Start Humidity is less than stop Humidity, Turn ON humidification mode 'E'.
2>. Dehumidification Mode 'd':
Relay turn ON and Green Indicator turn ON and Dehumidification equipment starts working if connect load when Current Humidity is more than Start Humidity.
Relay turn OFF and RED Indicator turn OFF and Dehumidification equipment stops working if connect load when Current Humidity is less than Stop Humidity.
3>. Humidification mode 'E':
Relay turn ON and Green Indicator turn ON and Humidification equipment starts working if connect load when Current Humidity is less than Start Humidity.
Relay turn OFF and Green Indicator turn OFF and Humidification equipment stops working if connect load when Current Humidity is more than Stop Humidity.
4>.Humidity Correction ‘ RH ’(-10.0~10.0%RH):
The system may have errors if it works for a long time, it can be corrected by this function.
Actual Humidity= Measured Humidity+ Calibration Value.
4.1>.Double-click button 'TM+' in the normal running interface into Temperature Correction setting interface.The first line shows the type of correction value(OFE or RH).The second line shows the specific value.
4.2>.Switch to select modified parameters by short press button ‘TM-’.
4.3>.Short press button ‘RH+’ and ‘RH-’ to set the specific value.Support long press.
4.4>.After the parameters have been modified, double-click button ‘TM+’ to save the data and exit the correction value setting interface.
5>.Set Start/Stop Humidity:
Keep press button 'RH+' for 3second in the normal running interface into Start Humidity setting interface.Short press button 'RH+' or 'RH-' to set parameters value.After the parameters are modified and then wait for 6s to automatically save and exit.
Keep press button 'RH-' for 3second in the normal running interface into Stop Humidity setting interface.Short press button 'RH+' or 'RH-' to set parameters value.After the parameters are modified and then wait for 6s to automatically save and exit.
6>.Relay enable (default on):
Short press button ‘RH-’ in the normal running interface.Turn ON or OFF humidity relay output enable.Screen will display ‘%’ and flashes if If the temperature relay is OFF.

Using Steps:
1>. Connect sensor to controller;
2>. Connect to power supply to controller;
3>. Adjust Start Temperature, Stop temperature and Temperature Correction;
4>. Adjust Start Humidity, Stop Humidity and Humidity Correction;
5>. Enable relay output according requirement;
6>. Remove power supply;
7>. Connect to load with power supply at relay output terminal if need at Step5;
8>. Connect to power supply for controller again;
9>. Test and working!

Additional Features:
1>. Set or read data by UART.
Parameters such as start temperature/humidity, stop temperature/humidity, temperature/humidity correction, etc. can be set through the UART.
2>. Temperature/Humidity real-time reporting.
The controller module will report the current temperature/humidity to the terminal equipment by the UART at intervals of 1 second to facilitate data acquisition if the temperature/humidity reporting function is turned ON.
3>. Relay enable (default on).
If the relay enable is turned off, the relay remains off.
That is, the output state will never change, no matter what the measured temperature/humidity is.


UART Communication and Parameter Settings:
The system supports UART data upload and parameter setting functions (TTL level);
UART: 9600, 8, 1

NO.CommandFunction
1StartStart test value report
2StopStop test value report
3ReadRead setting parameters
4T:ONTemperature Relay enable ON
5T:OFFTemperature Relay enable OFF
6H:ONHumidity Relay enable ON
7H:OFFHumidity Relay enable OFF
8TS:XX.XSet Start Temperature Value (-20.0~60.0℃)
9TP:XX.XSet Stop Temperature Value (-20.0~60.0℃)
10HS:XX.XSet Start Humidity Value (00.0%~100.0%RH)
11HP:XX.XSet Stop Humidity Value (00.0%~100.0%RH)
12TC:XX.XTemperature calibration (-10.0~10.0℃)
13HC:XX.XHumidity calibration (-10.0~10.0%RH)

Temperature and humidity data upload format:
Temperature format: work mode (H/C), Current Temperature, Temperature relay status;
Humidity format: work mode (E/D), Current Humidity, Humidity relay status;
For example:
H, 20.5℃, CL: Heating Mode, Current Temperature 20.5℃, Temperature relay is OFF.
D, 50.4%,OP: Dehumidification mode, Current Humidity 50.4%RH, Humidity relay is ON.


نظر خود را بنویسید
*
*
1
دیدگاه کاربران
  • 1398-06-26

    سلام
    من این ماژول را گرفتم کیفیتش عالیه، جنس رله ها خوب بودند. وجود نمایشگر oled روی این ماژول خیلی کاربردیه سنسورش هم داخل گلخانه قرار دادم که بسیار عالی داره کار میکنه
    ممنونم از دانشجو کیت با اجناس با کیفیتشون

    پاسخ مدیر:

    با سلام


    از توجه شما سپاسگزاریم.

صفحه نمایش

نوع نمایشگر : OLED

تغذیه

ولتاژ مورد نياز : 12 ولت

ویژگی های فنی

دمای کاری : - 20 تا + 60 درجه سانتی گراد
کد تجاری ماژول و برد : XY-TR01

سایر مشخصات کالا

سطح تجربه مورد نیاز : حرفه ای
نوع کاربرد محصول : مناسب برای استفاده صنعتی
نوع برد - ماژول : دماسنج - Thermometer
سنسور : SHT20
خروجی : دارای خروجی رله
سایر توضیحات : رنج اندازه‌گیری رطوبت: 0%-100%RH
سایر قابلیت‌ها : دارای دو رله
بنچ مارک تیم فنی دانشجو کیت : 9 از 10
میکروفن خازنی Microphone مناسب پری آمپلی فایر
1,200تـومان
ناموجود
برد آردوینو مگا 2560- Arduino Mega2560 R3 ...
136,300تـومان
برد آردوینو Arduino Uno R3 با تراشه R3 اور...
62,200تـومان

محصولات مرتبط

چگونگی دریافت زمان دقیق در پروژه IoT از طریق سرور